|
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778 |
- Installation
- --------------------------------------------------------------------------------
-
- To install this library, just place this entire folder as a subfolder in your
- Arduino hardware/libraries folder.
-
- When installed, this library should look like:
-
- Arduino/hardware/libraries/ks0108 (this library's folder)
- Arduino/hardware/libraries/ks0108/ks0108.cpp (the library implementation file)
- Arduino/hardware/libraries/ks0108/ks0108.h (the library header file)
- Arduino/hardware/libraries/ks0108/ks0108_Panel.h (the Panel configuration header)
- Arduino/hardware/libraries/ks0108/ks0108_Arduino.h (header used to define pins for Atmega168/328)
- Arduino/hardware/libraries/ks0108/ks0108_Mega.h (header used to define pins for Mega)
- Arduino/hardware/libraries/ks0108/ks0108_Sanguino.h (header used to define pins for Sanguino) - untested
- Arduino/hardware/libraries/ks0108/SystemFont5x7.h (definition for 5x7 system fonmt)
- Arduino/hardware/libraries/ks0108/Arial14.h (the definition for 14 point Arial Font)
- Arduino/hardware/libraries/ks0108/keywords.txt (the syntax coloring file)
- Arduino/hardware/libraries/ks0108/examples (diectory containing the example test sketch)
- Arduino/hardware/libraries/ks0108/readme.txt (this file)
-
- Building
- --------------------------------------------------------------------------------
-
- After the files are copied into your library directory, check the wiring matches the pin configuration
- for your board. The defualt wiring is different for each of the three chip types:
- (see http://www.arduino.cc/playground/Code/GLCDks0108 for more info)
-
-
- ATmega168/328 uses configuration file: ks0108_Arduino.h
- LCD ARDUINO
- CSEL1 14 // CS1 Bit // swap with CSEL2 if left/right is reversed
- CSEL2 15 // CS2 Bit
- R_W 16 // R/W Bit
- D_I 17 // D/I Bit
- EN 18 // EN Bit
-
- LCD data 0-3 8-11
- LCD data 4-7 4-7
-
- Mega (ATmega1280) uses configuration file: ks0108_Mega.h
-
- CSEL1 33 // CS1 Bit // swap with CSEL2 if left/right is reversed
- CSEL2 34 // CS2 Bit
- R_W 35 // R/W Bit
- D_I 36 // D/I Bit
- EN 37 // EN Bit
-
- LCD data 0-7 22-29
-
- Sanguino (ATmega644) uses configuration file: ks0108_Sanguino.h
- CSEL1 24 // CS1 Bit // swap pin assignments with CSEL2 if left/right image is reversed
- CSEL2 25 // CS2 Bit
- R_W 26 // R/W Bit
- D_I 27 // D/I Bit
- EN 28 // EN Bit
-
- LCD data 0-7 16-23
-
- Slow panels may need delays added to the panel panel configuraion file: ks0108_Panel.h
- change the number 6 to a higher number to make th delay longer :
- #define EN_DELAY_VALUE 6 // this is the delay value that may need to be hand tuned for slow panels
- If your panel has a different width or height you can change these two constants in this file:
- #define DISPLAY_WIDTH 128
- #define DISPLAY_HEIGHT 64
-
- After a successful build of this library, a new file named 'ks0108.o' will appear
- in ks0108 library directory. If you make any changes to any of the files in the
- ks0108 directory you must delete ks0108.o before recompiling your sketch for the changes to be
- recognized by your sketch. The new "Test.o" with your code will appear after the next
- verify or compile (If there are no syntax errors in the changed code).
-
- To use the library in a sketch, go to the Sketch | Import Library menu and
- select ks0108. This will add a corresponding line to the top of your sketch:
- #include <ks0108.h>. It will also add lines for all the font definitions you have
- in the ks0108 library directory. You should remove the includes for any fonts you
- don't use in a sketch, they use a lot of program memory.
-
|
