teensy-core-4.1/teensy3/serial3.c

/* Teensyduino Core Library
 * http://www.pjrc.com/teensy/
 * Copyright (c) 2017 PJRC.COM, LLC.
 *
 * Permission is hereby granted, free of charge, to any person obtaining
 * a copy of this software and associated documentation files (the
 * "Software"), to deal in the Software without restriction, including
 * without limitation the rights to use, copy, modify, merge, publish,
 * distribute, sublicense, and/or sell copies of the Software, and to
 * permit persons to whom the Software is furnished to do so, subject to
 * the following conditions:
 *
 * 1. The above copyright notice and this permission notice shall be
 * included in all copies or substantial portions of the Software.
 *
 * 2. If the Software is incorporated into a build system that allows
 * selection among a list of target devices, then similar target
 * devices manufactured by PJRC.COM must be included in the list of
 * target devices and selectable in the same manner.
 *
 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
 * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
 * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
 * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
 * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
 * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
 * SOFTWARE.
 */

#include "kinetis.h"
#include "core_pins.h"
#include "HardwareSerial.h"

////////////////////////////////////////////////////////////////
// Tunable parameters (relatively safe to edit these numbers)
////////////////////////////////////////////////////////////////

#ifndef SERIAL3_TX_BUFFER_SIZE
#define SERIAL3_TX_BUFFER_SIZE     40 // number of outgoing bytes to buffer
#endif
#ifndef SERIAL3_RX_BUFFER_SIZE
#define SERIAL3_RX_BUFFER_SIZE     64 // number of incoming bytes to buffer
#endif
#define RTS_HIGH_WATERMARK (SERIAL3_RX_BUFFER_SIZE-24) // RTS requests sender to pause
#define RTS_LOW_WATERMARK  (SERIAL3_RX_BUFFER_SIZE-38) // RTS allows sender to resume
#define IRQ_PRIORITY  64  // 0 = highest priority, 255 = lowest


////////////////////////////////////////////////////////////////
// changes not recommended below this point....
////////////////////////////////////////////////////////////////

#ifdef SERIAL_9BIT_SUPPORT
static uint8_t use9Bits = 0;
#define BUFTYPE uint16_t
#else
#define BUFTYPE uint8_t
#define use9Bits 0
#endif

static volatile BUFTYPE tx_buffer[SERIAL3_TX_BUFFER_SIZE];
static volatile BUFTYPE rx_buffer[SERIAL3_RX_BUFFER_SIZE];
static volatile uint8_t transmitting = 0;
#if defined(KINETISK)
  static volatile uint8_t *transmit_pin=NULL;
  #define transmit_assert()   *transmit_pin = 1
  #define transmit_deassert() *transmit_pin = 0
  static volatile uint8_t *rts_pin=NULL;
  #define rts_assert()        *rts_pin = 0
  #define rts_deassert()      *rts_pin = 1
#elif defined(KINETISL)
  static volatile uint8_t *transmit_pin=NULL;
  static uint8_t transmit_mask=0;
  #define transmit_assert()   *(transmit_pin+4) = transmit_mask;
  #define transmit_deassert() *(transmit_pin+8) = transmit_mask;
  static volatile uint8_t *rts_pin=NULL;
  static uint8_t rts_mask=0;
  #define rts_assert()        *(rts_pin+8) = rts_mask;
  #define rts_deassert()      *(rts_pin+4) = rts_mask;
#endif
#if SERIAL3_TX_BUFFER_SIZE > 65535
static volatile uint32_t tx_buffer_head = 0;
static volatile uint32_t tx_buffer_tail = 0;
#elif SERIAL3_TX_BUFFER_SIZE > 255
static volatile uint16_t tx_buffer_head = 0;
static volatile uint16_t tx_buffer_tail = 0;
#else
static volatile uint8_t tx_buffer_head = 0;
static volatile uint8_t tx_buffer_tail = 0;
#endif
#if SERIAL3_RX_BUFFER_SIZE > 65535
static volatile uint32_t rx_buffer_head = 0;
static volatile uint32_t rx_buffer_tail = 0;
#elif SERIAL3_RX_BUFFER_SIZE > 255
static volatile uint16_t rx_buffer_head = 0;
static volatile uint16_t rx_buffer_tail = 0;
#else
static volatile uint8_t rx_buffer_head = 0;
static volatile uint8_t rx_buffer_tail = 0;
#endif
#if defined(KINETISL)
static uint8_t rx_pin_num = 7;
#endif
static uint8_t tx_pin_num = 8;

// UART0 and UART1 are clocked by F_CPU, UART2 is clocked by F_BUS
// UART0 has 8 byte fifo, UART1 and UART2 have 1 byte buffer

#define C2_ENABLE		UART_C2_TE | UART_C2_RE | UART_C2_RIE
#define C2_TX_ACTIVE		C2_ENABLE | UART_C2_TIE
#define C2_TX_COMPLETING	C2_ENABLE | UART_C2_TCIE
#define C2_TX_INACTIVE		C2_ENABLE

void serial3_begin(uint32_t divisor)
{
	SIM_SCGC4 |= SIM_SCGC4_UART2;	// turn on clock, TODO: use bitband
	rx_buffer_head = 0;
	rx_buffer_tail = 0;
	tx_buffer_head = 0;
	tx_buffer_tail = 0;
	transmitting = 0;
#if defined(KINETISK)
	CORE_PIN7_CONFIG = PORT_PCR_PE | PORT_PCR_PS | PORT_PCR_PFE | PORT_PCR_MUX(3);
	CORE_PIN8_CONFIG = PORT_PCR_DSE | PORT_PCR_SRE | PORT_PCR_MUX(3);
#elif defined(KINETISL)
	switch (rx_pin_num) {
		case 7: CORE_PIN7_CONFIG = PORT_PCR_PE | PORT_PCR_PS | PORT_PCR_PFE | PORT_PCR_MUX(3); break;
		case 6: CORE_PIN6_CONFIG = PORT_PCR_PE | PORT_PCR_PS | PORT_PCR_PFE | PORT_PCR_MUX(3); break;
	}
	switch (tx_pin_num) {
		case 8:  CORE_PIN8_CONFIG = PORT_PCR_DSE | PORT_PCR_SRE | PORT_PCR_MUX(3); break;
		case 20: CORE_PIN20_CONFIG = PORT_PCR_DSE | PORT_PCR_SRE | PORT_PCR_MUX(3); break;
	}
#endif
#if defined(HAS_KINETISK_UART2)
	if (divisor < 32) divisor = 32;
	UART2_BDH = (divisor >> 13) & 0x1F;
	UART2_BDL = (divisor >> 5) & 0xFF;
	UART2_C4 = divisor & 0x1F;
	UART2_C1 = 0;
	UART2_PFIFO = 0;
#elif defined(HAS_KINETISL_UART2)
	if (divisor < 1) divisor = 1;
	UART2_BDH = (divisor >> 8) & 0x1F;
	UART2_BDL = divisor & 0xFF;
	UART2_C1 = 0;
#endif
	UART2_C2 = C2_TX_INACTIVE;
	NVIC_SET_PRIORITY(IRQ_UART2_STATUS, IRQ_PRIORITY);
	NVIC_ENABLE_IRQ(IRQ_UART2_STATUS);
}

void serial3_format(uint32_t format)
{
	uint8_t c;

	c = UART2_C1;
	c = (c & ~0x13) | (format & 0x03);	// configure parity
	if (format & 0x04) c |= 0x10;		// 9 bits (might include parity)
	UART2_C1 = c;
	if ((format & 0x0F) == 0x04) UART2_C3 |= 0x40; // 8N2 is 9 bit with 9th bit always 1
	c = UART2_S2 & ~0x10;
	if (format & 0x10) c |= 0x10;		// rx invert
	UART2_S2 = c;
	c = UART2_C3 & ~0x10;
	if (format & 0x20) c |= 0x10;		// tx invert
	UART2_C3 = c;
#if defined(SERIAL_9BIT_SUPPORT) && !defined(KINETISL)
	c = UART2_C4 & 0x1F;
	if (format & 0x08) c |= 0x20;		// 9 bit mode with parity (requires 10 bits)
	UART2_C4 = c;
	use9Bits = format & 0x80;
#endif
#if defined(__MK64FX512__) || defined(__MK66FX1M0__) || defined(KINETISL)
	// For T3.5/T3.6/TLC See about turning on 2 stop bit mode
	if ( format & 0x100) {
		uint8_t bdl = UART2_BDL;
		UART2_BDH |= UART_BDH_SBNS;		// Turn on 2 stop bits - was turned off by set baud
		UART2_BDL = bdl;		// Says BDH not acted on until BDL is written
	}
#endif

}

void serial3_end(void)
{
	if (!(SIM_SCGC4 & SIM_SCGC4_UART2)) return;
	while (transmitting) yield();  // wait for buffered data to send
	NVIC_DISABLE_IRQ(IRQ_UART2_STATUS);
	UART2_C2 = 0;
	#if defined(KINETISK)
	CORE_PIN7_CONFIG = PORT_PCR_PE | PORT_PCR_PS | PORT_PCR_MUX(1);
	CORE_PIN8_CONFIG = PORT_PCR_PE | PORT_PCR_PS | PORT_PCR_MUX(1);
	#elif defined(KINETISL)
	switch (rx_pin_num) {
		case 7: CORE_PIN7_CONFIG = PORT_PCR_PE | PORT_PCR_PS | PORT_PCR_MUX(1); break;
		case 6: CORE_PIN6_CONFIG = PORT_PCR_PE | PORT_PCR_PS | PORT_PCR_MUX(1); break;
	}
	switch (tx_pin_num & 127) {
		case 8:  CORE_PIN8_CONFIG = PORT_PCR_PE | PORT_PCR_PS | PORT_PCR_MUX(1); break;
		case 20: CORE_PIN20_CONFIG = PORT_PCR_PE | PORT_PCR_PS | PORT_PCR_MUX(1); break;
	}
	#endif	
	UART2_S1;
	UART2_D; // clear leftover error status
	rx_buffer_head = 0;
	rx_buffer_tail = 0;
	if (rts_pin) rts_deassert();
}

void serial3_set_transmit_pin(uint8_t pin)
{
	while (transmitting) ;
	pinMode(pin, OUTPUT);
	digitalWrite(pin, LOW);
	transmit_pin = portOutputRegister(pin);
	#if defined(KINETISL)
	transmit_mask = digitalPinToBitMask(pin);
	#endif
}

void serial3_set_tx(uint8_t pin, uint8_t opendrain)
{
	uint32_t cfg;

	if (opendrain) pin |= 128;
	if (pin == tx_pin_num) return;
	if ((SIM_SCGC4 & SIM_SCGC4_UART2)) {
		switch (tx_pin_num & 127) {
			case 8:  CORE_PIN8_CONFIG = 0; break; // PTD3
	#if defined(KINETISL)
			case 20: CORE_PIN20_CONFIG = 0; break; // PTD5
	#endif
		}
		if (opendrain) {
			cfg = PORT_PCR_DSE | PORT_PCR_ODE;
		} else {
			cfg = PORT_PCR_DSE | PORT_PCR_SRE;
		}
		switch (pin & 127) {
			case 8:  CORE_PIN8_CONFIG = cfg | PORT_PCR_MUX(3); break;
	#if defined(KINETISL)
			case 20: CORE_PIN20_CONFIG = cfg | PORT_PCR_MUX(3); break;
	#endif
		}
	}
	tx_pin_num = pin;
}

void serial3_set_rx(uint8_t pin)
{
	#if defined(KINETISL)
	if (pin == rx_pin_num) return;
	if ((SIM_SCGC4 & SIM_SCGC4_UART2)) {
		switch (rx_pin_num) {
			case 7: CORE_PIN7_CONFIG = 0; break; // PTD2
			case 6: CORE_PIN6_CONFIG = 0; break; // PTD4
		}
		switch (pin) {
			case 7: CORE_PIN7_CONFIG = PORT_PCR_PE | PORT_PCR_PS | PORT_PCR_PFE | PORT_PCR_MUX(3); break;
			case 6: CORE_PIN6_CONFIG = PORT_PCR_PE | PORT_PCR_PS | PORT_PCR_PFE | PORT_PCR_MUX(3); break;
		}
	}
	rx_pin_num = pin;
	#endif
}

int serial3_set_rts(uint8_t pin)
{
	if (!(SIM_SCGC4 & SIM_SCGC4_UART2)) return 0;
	if (pin < CORE_NUM_DIGITAL) {
		rts_pin = portOutputRegister(pin);
		#if defined(KINETISL)
		rts_mask = digitalPinToBitMask(pin);
		#endif
		pinMode(pin, OUTPUT);
		rts_assert();
	} else {
		rts_pin = NULL;
		return 0;
	}
/*
	if (pin == 2) {
		CORE_PIN2_CONFIG = PORT_PCR_MUX(3);
	} else {
		UART2_MODEM &= ~UART_MODEM_RXRTSE;
		return 0;
	}
	UART2_MODEM |= UART_MODEM_RXRTSE;
*/
	return 1;
}

int serial3_set_cts(uint8_t pin)
{
#if defined(KINETISK)
	if (!(SIM_SCGC4 & SIM_SCGC4_UART2)) return 0;
	if (pin == 14) {
		CORE_PIN14_CONFIG = PORT_PCR_MUX(3) | PORT_PCR_PE; // weak pulldown
	} else {
		UART2_MODEM &= ~UART_MODEM_TXCTSE;
		return 0;
	}
	UART2_MODEM |= UART_MODEM_TXCTSE;
	return 1;
#else
	return 0;
#endif
}

void serial3_putchar(uint32_t c)
{
	uint32_t head, n;

	if (!(SIM_SCGC4 & SIM_SCGC4_UART2)) return;
	if (transmit_pin) transmit_assert();
	head = tx_buffer_head;
	if (++head >= SERIAL3_TX_BUFFER_SIZE) head = 0;
	while (tx_buffer_tail == head) {
		int priority = nvic_execution_priority();
		if (priority <= IRQ_PRIORITY) {
			if ((UART2_S1 & UART_S1_TDRE)) {
				uint32_t tail = tx_buffer_tail;
				if (++tail >= SERIAL3_TX_BUFFER_SIZE) tail = 0;
				n = tx_buffer[tail];
				if (use9Bits) UART2_C3 = (UART2_C3 & ~0x40) | ((n & 0x100) >> 2);
				UART2_D = n;
				tx_buffer_tail = tail;
			}
		} else if (priority >= 256) {
			yield(); // wait
		}
	}
	tx_buffer[head] = c;
	transmitting = 1;
	tx_buffer_head = head;
	UART2_C2 = C2_TX_ACTIVE;
}

void serial3_write(const void *buf, unsigned int count)
{
	const uint8_t *p = (const uint8_t *)buf;
	while (count-- > 0) serial3_putchar(*p++);
}

void serial3_flush(void)
{
	while (transmitting) yield(); // wait
}

int serial3_write_buffer_free(void)
{
	uint32_t head, tail;

	head = tx_buffer_head;
	tail = tx_buffer_tail;
	if (head >= tail) return SERIAL3_TX_BUFFER_SIZE - 1 - head + tail;
	return tail - head - 1;
}

int serial3_available(void)
{
	uint32_t head, tail;

	head = rx_buffer_head;
	tail = rx_buffer_tail;
	if (head >= tail) return head - tail;
	return SERIAL3_RX_BUFFER_SIZE + head - tail;
}

int serial3_getchar(void)
{
	uint32_t head, tail;
	int c;

	head = rx_buffer_head;
	tail = rx_buffer_tail;
	if (head == tail) return -1;
	if (++tail >= SERIAL3_RX_BUFFER_SIZE) tail = 0;
	c = rx_buffer[tail];
	rx_buffer_tail = tail;
	if (rts_pin) {
		int avail;
		if (head >= tail) avail = head - tail;
		else avail = SERIAL3_RX_BUFFER_SIZE + head - tail;
		if (avail <= RTS_LOW_WATERMARK) rts_assert();
	}
	return c;
}

int serial3_peek(void)
{
	uint32_t head, tail;

	head = rx_buffer_head;
	tail = rx_buffer_tail;
	if (head == tail) return -1;
	if (++tail >= SERIAL3_RX_BUFFER_SIZE) tail = 0;
	return rx_buffer[tail];
}

void serial3_clear(void)
{
	rx_buffer_head = rx_buffer_tail;
	if (rts_pin) rts_assert();
}

// status interrupt combines
//   Transmit data below watermark  UART_S1_TDRE
//   Transmit complete		    UART_S1_TC
//   Idle line			    UART_S1_IDLE
//   Receive data above watermark   UART_S1_RDRF
//   LIN break detect		    UART_S2_LBKDIF
//   RxD pin active edge	    UART_S2_RXEDGIF

void uart2_status_isr(void)
{
	uint32_t head, tail, n;
	uint8_t c;

	if (UART2_S1 & UART_S1_RDRF) {
		if (use9Bits && (UART2_C3 & 0x80)) {
			n = UART2_D | 0x100;
		} else {
			n = UART2_D;
		}
		head = rx_buffer_head + 1;
		if (head >= SERIAL3_RX_BUFFER_SIZE) head = 0;
		if (head != rx_buffer_tail) {
			rx_buffer[head] = n;
			rx_buffer_head = head;
		}
		if (rts_pin) {
			int avail;
			tail = tx_buffer_tail;
			if (head >= tail) avail = head - tail;
			else avail = SERIAL3_RX_BUFFER_SIZE + head - tail;
			if (avail >= RTS_HIGH_WATERMARK) rts_deassert();
		}
	}
	c = UART2_C2;
	if ((c & UART_C2_TIE) && (UART2_S1 & UART_S1_TDRE)) {
		head = tx_buffer_head;
		tail = tx_buffer_tail;
		if (head == tail) {
			UART2_C2 = C2_TX_COMPLETING;
		} else {
			if (++tail >= SERIAL3_TX_BUFFER_SIZE) tail = 0;
			n = tx_buffer[tail];
			if (use9Bits) UART2_C3 = (UART2_C3 & ~0x40) | ((n & 0x100) >> 2);
			UART2_D = n;
			tx_buffer_tail = tail;
		}
	}
	if ((c & UART_C2_TCIE) && (UART2_S1 & UART_S1_TC)) {
		transmitting = 0;
		if (transmit_pin) transmit_deassert();
		UART2_C2 = C2_TX_INACTIVE;
	}
}