teensy-sdfat/SdFat/examples/PrintBenchmark/PrintBenchmark.ino

/*
 * This sketch is a simple Print benchmark.
 */
#include <SdFat.h>
#include <SdFatUtil.h>

// SD chip select pin
const uint8_t chipSelect = SS;

// number of lines to print
const uint16_t N_PRINT = 20000;

// file system
SdFat sd;

// test file
SdFile file;

// Serial output stream
ArduinoOutStream cout(Serial);
//------------------------------------------------------------------------------
// store error strings in flash to save RAM
#define error(s) sd.errorHalt_P(PSTR(s))
//------------------------------------------------------------------------------
void setup() {
  Serial.begin(9600);
  while (!Serial) {
    // wait for Leonardo
  }
}
//------------------------------------------------------------------------------
void loop() {
  uint32_t maxLatency;
  uint32_t minLatency;
  uint32_t totalLatency;

  while (Serial.read() >= 0) {
  }
  // pstr stores strings in flash to save RAM
  cout << pstr("Type any character to start\n");
  while (Serial.read() <= 0) {
  }
  delay(400);  // catch Due reset problem

  cout << pstr("Free RAM: ") << FreeRam() << endl;

  // initialize the SD card at SPI_FULL_SPEED for best performance.
  // try SPI_HALF_SPEED if bus errors occur.
  if (!sd.begin(chipSelect, SPI_FULL_SPEED)) sd.initErrorHalt();

  cout << pstr("Type is FAT") << int(sd.vol()->fatType()) << endl;

  cout << pstr("Starting print test.  Please wait.\n\n");

  // do write test
  for (int test = 0; test < 6; test++) {
    char fileName[13] = "BENCH0.TXT";
    fileName[5] = '0' + test;
    // open or create file - truncate existing file.
    if (!file.open(fileName, O_CREAT | O_TRUNC | O_RDWR)) {
      error("open failed");
    }
    maxLatency = 0;
    minLatency = 999999;
    totalLatency = 0;
    switch(test) {
    case 0:
      cout << pstr("Test of println(uint16_t)\n");
      break;

    case 1:
      cout << pstr("Test of printField(uint16_t, char)\n");
      break;

    case 2:
      cout << pstr("Test of println(uint32_t)\n");
      break;
      
    case 3:
      cout << pstr("Test of printField(uint32_t, char)\n");
      break;      
    case 4:
      cout << pstr("Test of println(float)\n");
      break;     
    
    case 5:
      cout << pstr("Test of printField(float, char)\n");
      break;         
    }
    
    uint32_t t = millis();
    for (uint16_t i = 0; i < N_PRINT; i++) {
      uint32_t m = micros();

      switch(test) {
      case 0:
        file.println(i);
        break;

      case 1:
        file.printField(i, '\n');
        break;

      case 2:
        file.println(12345678UL + i);
        break;     
      
      case 3:
        file.printField(12345678UL + i, '\n');
        break;        
        
      case 4:
        file.println((float)0.01*i);
        break;
      
      case 5:
        file.printField((float)0.01*i, '\n');
        break;
      }
      if (file.writeError) {
        error("write failed");
      }
      m = micros() - m;
      if (maxLatency < m) maxLatency = m;
      if (minLatency > m) minLatency = m;
      totalLatency += m;
    }
    file.close();
    t = millis() - t;
    double s = file.fileSize();
    cout << pstr("Time ") << 0.001*t << pstr(" sec\n");
    cout << pstr("File size ") << 0.001*s << pstr(" KB\n");
    cout << pstr("Write ") << s/t << pstr(" KB/sec\n");
    cout << pstr("Maximum latency: ") << maxLatency;
    cout << pstr(" usec, Minimum Latency: ") << minLatency;
    cout << pstr(" usec, Avg Latency: ");
    cout << totalLatency/N_PRINT << pstr(" usec\n\n");
  }
  cout << pstr("Done!\n\n");
}