visus
/
teensy-sdfat
Sledovat 1
Oblíbit 0
Rozštěpit 0
Zdrojový kód Úkoly 0 Požadavky na natažení 0 Vydání 0 Wiki Aktivita
Nelze vybrat více než 25 témat Téma musí začínat písmenem nebo číslem, může obsahovat pomlčky („-“) a může být dlouhé až 35 znaků.
59 Revize
1 Větev
Strom: 97f98028a0
Větve Značky
${ item.name }
Vytvořit větev ${ searchTerm }
z „97f98028a0“
${ noResults }
teensy-sdfat/extras/SdErrorCodes.txt

51 lines
2.3KB
Surový Blame Historie 

  1. 2019-12-10

  2. 

  3. Run the SdErrorCode example to produce an updated list.

  4. 

  5. C

  6. Code,Symbol - failed operation

  7. 0X00,SD_CARD_ERROR_NONE - No error

  8. 0X01,SD_CARD_ERROR_CMD0 - Card reset failed

  9. 0X02,SD_CARD_ERROR_CMD2 - SDIO read CID

  10. 0X03,SD_CARD_ERROR_CMD3 - SDIO publish RCA

  11. 0X04,SD_CARD_ERROR_CMD6 - Switch card function

  12. 0X05,SD_CARD_ERROR_CMD7 - SDIO card select

  13. 0X06,SD_CARD_ERROR_CMD8 - Send and check interface settings

  14. 0X07,SD_CARD_ERROR_CMD9 - Read CSD data

  15. 0X08,SD_CARD_ERROR_CMD10 - Read CID data

  16. 0X09,SD_CARD_ERROR_CMD12 - Stop multiple block read

  17. 0X0A,SD_CARD_ERROR_CMD13 - Read card status

  18. 0X0B,SD_CARD_ERROR_CMD17 - Read single block

  19. 0X0C,SD_CARD_ERROR_CMD18 - Read multiple blocks

  20. 0X0D,SD_CARD_ERROR_CMD24 - Write single block

  21. 0X0E,SD_CARD_ERROR_CMD25 - Write multiple blocks

  22. 0X0F,SD_CARD_ERROR_CMD32 - Set first erase block

  23. 0X10,SD_CARD_ERROR_CMD33 - Set last erase block

  24. 0X11,SD_CARD_ERROR_CMD38 - Erase selected blocks

  25. 0X12,SD_CARD_ERROR_CMD58 - Read OCR register

  26. 0X13,SD_CARD_ERROR_CMD59 - Set CRC mode

  27. 0X14,SD_CARD_ERROR_ACMD6 - Set SDIO bus width

  28. 0X15,SD_CARD_ERROR_ACMD13 - Read extended status

  29. 0X16,SD_CARD_ERROR_ACMD23 - Set pre-erased count

  30. 0X17,SD_CARD_ERROR_ACMD41 - Activate card initialization

  31. 0X18,SD_CARD_ERROR_READ_TOKEN - Bad read data token

  32. 0X19,SD_CARD_ERROR_READ_CRC - Read CRC error

  33. 0X1A,SD_CARD_ERROR_READ_FIFO - SDIO fifo read timeout

  34. 0X1B,SD_CARD_ERROR_READ_REG - Read CID or CSD failed.

  35. 0X1C,SD_CARD_ERROR_READ_START - Bad readStart argument

  36. 0X1D,SD_CARD_ERROR_READ_TIMEOUT - Read data timeout

  37. 0X1E,SD_CARD_ERROR_STOP_TRAN - Multiple block stop failed

  38. 0X1F,SD_CARD_ERROR_WRITE_DATA - Write data not accepted

  39. 0X20,SD_CARD_ERROR_WRITE_FIFO - SDIO fifo write timeout

  40. 0X21,SD_CARD_ERROR_WRITE_START - Bad writeStart argument

  41. 0X22,SD_CARD_ERROR_WRITE_PROGRAMMING - Flash programming

  42. 0X23,SD_CARD_ERROR_WRITE_TIMEOUT - Write timeout

  43. 0X24,SD_CARD_ERROR_DMA - DMA transfer failed

  44. 0X25,SD_CARD_ERROR_ERASE - Card did not accept erase commands

  45. 0X26,SD_CARD_ERROR_ERASE_SINGLE_SECTOR - Card does not support erase

  46. 0X27,SD_CARD_ERROR_ERASE_TIMEOUT - Erase command timeout

  47. 0X28,SD_CARD_ERROR_INIT_NOT_CALLED - Card has not been initialized

  48. 0X29,SD_CARD_ERROR_INVALID_CARD_CONFIG - Invalid card config

  49. 0X2A,SD_CARD_ERROR_FUNCTION_NOT_SUPPORTED - Unsupported SDIO command

  50. 0X2B,SD_CARD_ERROR_UNKNOWN - Unknown error