Merge pull request #27 from eriknyquist/master

Minor additions to example sketches for Arduino 101 compatibility

examples/CopyFromSD/CopyFromSD.ino

@@ -4,6 +4,9 @@
 
 const int SDchipSelect = 4;    // Audio Shield has SD card CS on pin 10
 const int FlashChipSelect = 6; // digital pin for flash chip CS pin
+// Uncomment this line if using the built-in SPI Flash device
+// on an Arduino 101 board
+//const int FlashChipSelect = 21;
 
 void setup() {
   //uncomment these if using Teensy audio shield
@@ -15,6 +18,8 @@ void setup() {
   //pinMode(4, INPUT_PULLUP);
   //pinMode(10, INPUT_PULLUP);
 
+  Serial.begin(9600);
+
   // wait up to 10 seconds for Arduino Serial Monitor
   unsigned long startMillis = millis();
   while (!Serial && (millis() - startMillis < 10000)) ;

examples/CopyFromSerial/CopyFromSerial.ino

@@ -83,6 +83,9 @@
 #define MISO              12
 #define SCK               14
 #define CSPIN              6
+// Uncomment this line if using the built-in SPI Flash device
+// on an Arduino 101 board
+//#define CSPIN            21
 
 void setup(){
   Serial.begin(9600);  //Teensy serial is always at full USB speed and buffered... the baud rate here is required but ignored

examples/EraseEverything/EraseEverything.ino

@@ -2,6 +2,9 @@
 #include <SPI.h>
 
 const int FlashChipSelect = 6; // digital pin for flash chip CS pin
+// Uncomment this line if using the built-in SPI Flash device
+// on an Arduino 101 board
+//const int FlashChipSelect = 21;
 
 SerialFlashFile file;
 
@@ -17,6 +20,8 @@ void setup() {
   //pinMode(4, INPUT_PULLUP);
   //pinMode(10, INPUT_PULLUP);
 
+  Serial.begin(9600);
+
   // wait up to 10 seconds for Arduino Serial Monitor
   unsigned long startMillis = millis();
   while (!Serial && (millis() - startMillis < 10000)) ;

examples/ListFiles/ListFiles.ino

@@ -2,6 +2,9 @@
 #include <SPI.h>
 
 const int FlashChipSelect = 6; // digital pin for flash chip CS pin
+// Uncomment this line if using the built-in SPI Flash device
+// on an Arduino 101 board
+//const int FlashChipSelect = 21;
 
 void setup() {
   //uncomment these if using Teensy audio shield
@@ -13,6 +16,8 @@ void setup() {
   //pinMode(4, INPUT_PULLUP);
   //pinMode(10, INPUT_PULLUP);
 
+  Serial.begin(9600);
+
   // wait for Arduino Serial Monitor
   while (!Serial) ;
   delay(100);

examples/MP3Player/MP3Player.ino

@@ -27,8 +27,12 @@ AudioConnection          patchCord3(mixer1, dac1);
 
 #define PROP_AMP_ENABLE    5
 #define FLASH_CHIP_SELECT  6
+// Uncomment this line if using the built-in SPI Flash device
+// on an Arduino 101 board
+//#define FLASH_CHIP_SELECT 21
 
 void setup() {
+  Serial.begin(9600);
   AudioMemory(8); //4
   delay(2000);
 

examples/RawHardwareTest/RawHardwareTest.ino

@@ -22,6 +22,9 @@
 #include <SPI.h>
 
 const int FlashChipSelect = 6; // digital pin for flash chip CS pin
+// Uncomment this line if using the built-in SPI Flash device
+// on an Arduino 101 board
+//const int FlashChipSelect = 21;
 
 SerialFlashFile file;
 
@@ -38,6 +41,8 @@ void setup() {
   //pinMode(4, INPUT_PULLUP);
   //pinMode(10, INPUT_PULLUP);
 
+  Serial.begin(9600);
+
   while (!Serial) ;
   delay(100);