visus
/
teensy-wire
Следить 1
В избранное 0
Форкнуть 0
Код Задачи 0 Pull Request'ы 0 Релизы 0 Вики Активность
Просмотр исходного кода

Improve FIFO handling for Teensy 4.0

main
PaulStoffregen 4 лет назад
Родитель
c93e869a96
Сommit
956a5c418a
2 измененных файлов: 152 добавлений и 166 удалений
Разделённый вид Показать статистику Diff
  1. +150
    -166
      WireIMXRT.cpp
  2. +2
    -0
      WireIMXRT.h

+ 150
- 166
WireIMXRT.cpp Просмотреть файл

@@ -2,33 +2,33 @@
#include "Wire.h"


#if defined(__IMXRT1052__) || defined(__IMXRT1062__)
#if defined(__IMXRT1062__)

#include "debug/printf.h"
//#include "debug/printf.h"

#define PINCONFIG (IOMUXC_PAD_ODE | IOMUXC_PAD_SRE | IOMUXC_PAD_DSE(4) | IOMUXC_PAD_SPEED(1) | IOMUXC_PAD_PKE | IOMUXC_PAD_PUE | IOMUXC_PAD_PUS(3))

void TwoWire::begin(void)
{
// use 24 MHz clock
CCM_CSCDR2 = (CCM_CSCDR2 & ~CCM_CSCDR2_LPI2C_CLK_PODF(63)) | CCM_CSCDR2_LPI2C_CLK_SEL;
// use 24 MHz clock
CCM_CSCDR2 = (CCM_CSCDR2 & ~CCM_CSCDR2_LPI2C_CLK_PODF(63)) | CCM_CSCDR2_LPI2C_CLK_SEL;
hardware.clock_gate_register |= hardware.clock_gate_mask;
port->MCR = LPI2C_MCR_RST;
setClock(100000);
port->MCR = LPI2C_MCR_RST;
setClock(100000);

// Setup SDA register
// Setup SDA register
*(portControlRegister(hardware.sda_pins[sda_pin_index_].pin)) = PINCONFIG;
*(portConfigRegister(hardware.sda_pins[sda_pin_index_].pin)) = hardware.sda_pins[sda_pin_index_].mux_val;
if (hardware.sda_pins[sda_pin_index_].select_input_register) {
*(hardware.sda_pins[sda_pin_index_].select_input_register) = hardware.sda_pins[sda_pin_index_].select_val;
}
*(hardware.sda_pins[sda_pin_index_].select_input_register) = hardware.sda_pins[sda_pin_index_].select_val;
}

// setup SCL register
*(portControlRegister(hardware.scl_pins[scl_pin_index_].pin)) = PINCONFIG;
*(portConfigRegister(hardware.scl_pins[scl_pin_index_].pin)) = hardware.scl_pins[scl_pin_index_].mux_val;
if (hardware.scl_pins[scl_pin_index_].select_input_register) {
*(hardware.scl_pins[scl_pin_index_].select_input_register) = hardware.scl_pins[scl_pin_index_].select_val;
}
*(hardware.scl_pins[scl_pin_index_].select_input_register) = hardware.scl_pins[scl_pin_index_].select_val;
}
}

void TwoWire::begin(uint8_t address)
@@ -56,12 +56,10 @@ void TwoWire::setSDA(uint8_t pin) {
*(portControlRegister(hardware.sda_pins[newindex].pin)) |= IOMUXC_PAD_PKE | IOMUXC_PAD_PUE | IOMUXC_PAD_PUS(3);
*(portConfigRegister(hardware.sda_pins[newindex].pin)) = hardware.sda_pins[newindex].mux_val;
if (hardware.sda_pins[newindex].select_input_register) {
*(hardware.sda_pins[newindex].select_input_register) = hardware.sda_pins[newindex].select_val;
}

*(hardware.sda_pins[newindex].select_input_register) = hardware.sda_pins[newindex].select_val;
}
}
sda_pin_index_ = newindex;

}

void TwoWire::setSCL(uint8_t pin) {
@@ -80,12 +78,43 @@ void TwoWire::setSCL(uint8_t pin) {
*(portControlRegister(hardware.scl_pins[newindex].pin)) |= IOMUXC_PAD_PKE | IOMUXC_PAD_PUE | IOMUXC_PAD_PUS(3);
*(portConfigRegister(hardware.scl_pins[newindex].pin)) = hardware.scl_pins[newindex].mux_val;
if (hardware.scl_pins[newindex].select_input_register) {
*(hardware.scl_pins[newindex].select_input_register) = hardware.scl_pins[newindex].select_val;
}

*(hardware.scl_pins[newindex].select_input_register) = hardware.scl_pins[newindex].select_val;
}
}
scl_pin_index_ = newindex;
}

bool TwoWire::force_clock()
{
bool ret = false;
uint32_t sda_pin = hardware.sda_pins[sda_pin_index_].pin;
uint32_t scl_pin = hardware.scl_pins[scl_pin_index_].pin;
uint32_t sda_mask = digitalPinToBitMask(sda_pin);
uint32_t scl_mask = digitalPinToBitMask(scl_pin);
// take control of pins with GPIO
*portConfigRegister(sda_pin) = 5 | 0x10;
*portSetRegister(sda_pin) = sda_mask;
*portModeRegister(sda_pin) |= sda_mask;
*portConfigRegister(scl_pin) = 5 | 0x10;
*portSetRegister(scl_pin) = scl_mask;
*portModeRegister(scl_pin) |= scl_mask;
delayMicroseconds(10);
for (int i=0; i < 9; i++) {
if ((*portInputRegister(sda_pin) & sda_mask)
&& (*portInputRegister(scl_pin) & scl_mask)) {
// success, both pins are high
ret = true;
break;
}
*portClearRegister(scl_pin) = scl_mask;
delayMicroseconds(5);
*portSetRegister(scl_pin) = scl_mask;
delayMicroseconds(5);
}
// return control of pins to I2C
*(portConfigRegister(sda_pin)) = hardware.sda_pins[sda_pin_index_].mux_val;
*(portConfigRegister(scl_pin)) = hardware.scl_pins[scl_pin_index_].mux_val;
return ret;
}

size_t TwoWire::write(uint8_t data)
@@ -116,198 +145,148 @@ size_t TwoWire::write(const uint8_t *data, size_t quantity)
return 0;
}

uint8_t TwoWire::endTransmission(uint8_t sendStop)
{
//printf("\nendTransmission %d (%x %x %x) %x\n", txBufferLength,txBuffer[0], txBuffer[1], txBuffer[2], sendStop);
uint32_t i=0, len, status;

len = txBufferLength;
if (!len) return 4; // no data to transmit

// wait while bus is busy

// 2 BBF = Bus Busy Flag
// 1 MBF = Master Busy Flag
// 40 DMF = Data Match Flag
// 20 PLTF = Pin Low Timeout Flag
// 10 FEF = FIFO Error Flag
// 08 ALF = Arbitration Lost Flag
// 04 NDF = NACK Detect Flag
// 02 SDF = STOP Detect Flag
// 01 EPF = End Packet Flag
// 2 RDF = Receive Data Flag
// 1 TDF = Transmit Data Flag

bool TwoWire::wait_idle()
{
elapsedMillis timeout = 0;
while (1) {
status = port->MSR; // pg 2899 & 2892
uint32_t status = port->MSR; // pg 2899 & 2892
if (!(status & LPI2C_MSR_BBF)) break; // bus is available
if (status & LPI2C_MSR_MBF) break; // we already have bus control
// TODO: timeout...
}
//printf("m=%x\n", status);

// Wonder if MFSR we should maybe clear it?
if ((port->MFSR & 0x7) &&
((port->MSR & (LPI2C_MSR_BBF|LPI2C_MSR_MBF)) != (LPI2C_MSR_BBF|LPI2C_MSR_MBF))) {
port->MCR = LPI2C_MCR_MEN | LPI2C_MCR_RTF; // clear the FIFO
port->MSR = LPI2C_MSR_PLTF | LPI2C_MSR_ALF | LPI2C_MSR_NDF | LPI2C_MSR_SDF | LPI2C_MSR_FEF; // clear flags
//printf("Clear TX Fifo %lx %lx\n", port->MSR, port->MFSR);
if (timeout > 16) {
//Serial.printf("timeout waiting for idle, MSR = %x\n", status);
if (force_clock()) break;
//Serial.printf("unable to get control of I2C bus\n");
return false;
}
}
// TODO: is this correct if the prior use didn't send stop?
//port->MSR = LPI2C_MSR_PLTF | LPI2C_MSR_ALF | LPI2C_MSR_NDF | LPI2C_MSR_SDF; // clear flags
port->MSR = status;
port->MSR = 0x00007F00; // clear all prior flags
return true;
}

//printf("MSR=%lX, MFSR=%lX\n", status, port->MFSR);
//elapsedMillis timeout=0;

uint8_t TwoWire::endTransmission(uint8_t sendStop)
{
uint32_t tx_len = txBufferLength;
if (!tx_len) return 4; // no address for transmit
if (!wait_idle()) return 4;
uint32_t tx_index = 0; // 0=start, 1=addr, 2-(N-1)=data, N=stop
elapsedMillis timeout = 0;
while (1) {
// transmit stuff, if we haven't already
if (i <= len) {
if (tx_index <= tx_len) {
uint32_t fifo_used = port->MFSR & 0x07; // pg 2914
//if (fifo_used < 4) printf("t=%ld\n", fifo_used);
while (fifo_used < 4) {
if (i == 0) {
//printf("start %x\n", txBuffer[0]);
if (tx_index == 0) {
port->MTDR = LPI2C_MTDR_CMD_START | txBuffer[0];
i = 1;
} else if (i < len) {
port->MTDR = LPI2C_MTDR_CMD_TRANSMIT | txBuffer[i++];
tx_index = 1;
} else if (tx_index < tx_len) {
port->MTDR = LPI2C_MTDR_CMD_TRANSMIT | txBuffer[tx_index++];
} else {
if (sendStop) port->MTDR = LPI2C_MTDR_CMD_STOP;
i++;
tx_index++;
break;
}
fifo_used = fifo_used + 1;
fifo_used++;
}
}
// monitor status
status = port->MSR; // pg 2899 & 2892
uint32_t status = port->MSR; // pg 2884 & 2891
if (status & LPI2C_MSR_ALF) {
//printf("arbitration lost\n");
port->MCR |= LPI2C_MCR_RTF | LPI2C_MCR_RRF; // clear FIFOs
return 4; // we lost bus arbitration to another master
}
if (status & LPI2C_MSR_NDF) {
//printf("NACK, f=%d, i=%d\n", port->MFSR & 0x07, i);
// TODO: check that hardware really sends stop automatically
port->MCR = LPI2C_MCR_MEN | LPI2C_MCR_RTF; // clear the FIFO
// TODO: is always sending a stop the right way to recover?
port->MCR |= LPI2C_MCR_RTF | LPI2C_MCR_RRF; // clear FIFOs
port->MTDR = LPI2C_MTDR_CMD_STOP;
return 2; // NACK for address
//return 3; // NACK for data TODO: how to discern addr from data?
return 2; // NACK (assume address, TODO: how to tell address from data)
}
//if (status & LPI2C_MSR_PLTF) {
//printf("bus stuck - what to do?\n");
//return 4;
//}

//if (timeout > 100) {
//printf("status = %x\n", status);
//timeout = 0;
//}

if (sendStop) {
if (status & LPI2C_MSR_SDF) {
// master automatically sends stop condition on some
// types of errors, so this flag only means success
// when all comments in fifo have been fully used
uint32_t fifo = port->MFSR & 0x07;
if (fifo == 0) return 0;
}
} else {
uint32_t fifo_used = port->MFSR & 0x07; // pg 2914
if (fifo_used == 0) {
//digitalWriteFast(15, HIGH);
//delayMicroseconds(2);
//digitalWriteFast(15, LOW);
// TODO: this returns before the last data transmits!
// Should verify every byte ACKs, arbitration not lost
//printf("fifo empty, msr=%x\n", status);
if ((status & LPI2C_MSR_PLTF) || timeout > 50) {
port->MCR |= LPI2C_MCR_RTF | LPI2C_MCR_RRF; // clear FIFOs
port->MTDR = LPI2C_MTDR_CMD_STOP; // try to send a stop
return 4; // clock stretched too long or generic timeout
}
// are we done yet?
if (tx_index > tx_len) {
uint32_t tx_fifo = port->MFSR & 0x07;
if (tx_fifo == 0 && ((status & LPI2C_MSR_SDF) || !sendStop)) {
return 0;
}
}
yield();
}
}

uint8_t TwoWire::requestFrom(uint8_t address, uint8_t length, uint8_t sendStop)
{
uint32_t cmd=0, status, fifo;

// wait while bus is busy
//printf("\nrequestFrom %x %x %x\n", address, length, sendStop);
while (1) {
status = port->MSR; // pg 2899 & 2892
if (!(status & LPI2C_MSR_BBF)) break; // bus is available
if (status & LPI2C_MSR_MBF) break; // we already have bus control
// TODO: timeout...
}
//printf("idle2, msr=%x\n", status);

// TODO: is this correct if the prior use didn't send stop?
port->MSR = LPI2C_MSR_PLTF | LPI2C_MSR_ALF | LPI2C_MSR_NDF | LPI2C_MSR_SDF | LPI2C_MSR_FEF; // clear flags

// these delays are an ugly kludge for BNO080
// https://forum.pjrc.com/threads/58268
// TODO: need more robust error recovery!!
if (status & (LPI2C_MSR_ALF | LPI2C_MSR_NDF)) {
delayMicroseconds(300); // min=120
} else if (status & (LPI2C_MSR_PLTF | LPI2C_MSR_FEF)) {
delayMicroseconds(60); // min=30
}

//printf("MSR=%lX, MCR:%lx, MFSR=%lX\n", status, port->MCR, port->MFSR);

// Wonder if MFSR we should maybe clear it?
if ((port->MFSR & 0x7) &&
((port->MSR & (LPI2C_MSR_BBF|LPI2C_MSR_MBF)) != (LPI2C_MSR_BBF|LPI2C_MSR_MBF))) {
port->MCR = LPI2C_MCR_MEN | LPI2C_MCR_RTF; // clear the FIFO
port->MSR = LPI2C_MSR_PLTF | LPI2C_MSR_ALF | LPI2C_MSR_NDF | LPI2C_MSR_SDF | LPI2C_MSR_FEF; // clear flags
//printf("Clear TX Fifo %lx %lx\n", port->MSR, port->MFSR);
}
if (!wait_idle()) return 4;
address = (address & 0x7F) << 1;
if (length < 1) length = 1;
if (length > 255) length = 255;
rxBufferIndex = 0;
rxBufferLength = 0;

//elapsedMillis timeout=0;

uint32_t tx_state = 0; // 0=begin, 1=start, 2=data, 3=stop
elapsedMillis timeout = 0;
while (1) {
// transmit stuff, if we haven't already
if (cmd < 3) {
fifo = port->MFSR & 0x07; // pg 2914
//if (fifo < 4) printf("t=%ld\n", fifo);
while (fifo < 4 && cmd < 3) {
if (cmd == 0) {
if (tx_state < 3) {
uint32_t tx_fifo = port->MFSR & 0x07; // pg 2914
while (tx_fifo < 4 && tx_state < 3) {
if (tx_state == 0) {
port->MTDR = LPI2C_MTDR_CMD_START | 1 | address;
} else if (cmd == 1) {
// causes bus stuck... need way to recover
//port->MTDR = LPI2C_MTDR_CMD_START | (length - 1);
} else if (tx_state == 1) {
port->MTDR = LPI2C_MTDR_CMD_RECEIVE | (length - 1);
} else {
if (sendStop) port->MTDR = LPI2C_MTDR_CMD_STOP;
}
cmd++;
fifo = fifo + 1;
tx_state++;
tx_fifo--;
}
}
// receive stuff
if (rxBufferLength < sizeof(rxBuffer)) {
fifo = (port->MFSR >> 16) & 0x07;
//if (fifo > 0) printf("r=%ld\n", fifo);
while (fifo > 0 && rxBufferLength < sizeof(rxBuffer)) {
uint32_t rx_fifo = (port->MFSR >> 16) & 0x07;
while (rx_fifo > 0 && rxBufferLength < sizeof(rxBuffer)) {
rxBuffer[rxBufferLength++] = port->MRDR;
fifo = fifo - 1;
rx_fifo--;
}
}
// monitor status
status = port->MSR; // pg 2899 & 2892
// monitor status, check for error conditions
uint32_t status = port->MSR; // pg 2884 & 2891
if (status & LPI2C_MSR_ALF) {
//printf("arbitration lost\n");
port->MCR |= LPI2C_MCR_RTF | LPI2C_MCR_RRF; // clear FIFOs
break;
}
if (status & LPI2C_MSR_NDF) {
//printf("got NACK\n");
// TODO: how to make sure stop is sent?
if ((status & LPI2C_MSR_NDF) || (status & LPI2C_MSR_PLTF) || timeout > 50) {
port->MCR |= LPI2C_MCR_RTF | LPI2C_MCR_RRF; // clear FIFOs
port->MTDR = LPI2C_MTDR_CMD_STOP; // try to send a stop
break;
}

//if (timeout > 250) {
//printf("Status = %x\n", status);
//timeout = 0;
//}

if (rxBufferLength >= length && cmd >= 3) break;
// are we done yet?
if (rxBufferLength >= length && tx_state >= 3) {
uint32_t tx_fifo = port->MFSR & 0x07;
if (tx_fifo == 0 && ((status & LPI2C_MSR_SDF) || !sendStop)) {
break;
}
}
yield();
}
//digitalWriteFast(15, HIGH);
//delayMicroseconds(2);
//digitalWriteFast(15, LOW);
uint32_t rx_fifo = (port->MFSR >> 16) & 0x07;
if (rx_fifo > 0) port->MCR |= LPI2C_MCR_RRF;
return rxBufferLength;
}

@@ -332,65 +311,70 @@ uint8_t TwoWire::requestFrom(uint8_t addr, uint8_t qty, uint32_t iaddr, uint8_t

PROGMEM
constexpr TwoWire::I2C_Hardware_t TwoWire::i2c1_hardware = {
CCM_CCGR2, CCM_CCGR2_LPI2C1(CCM_CCGR_ON),
CCM_CCGR2, CCM_CCGR2_LPI2C1(CCM_CCGR_ON),
{{18, 3 | 0x10, &IOMUXC_LPI2C1_SDA_SELECT_INPUT, 1}, {0xff, 0xff, nullptr, 0}},
{{19, 3 | 0x10, &IOMUXC_LPI2C1_SCL_SELECT_INPUT, 1}, {0xff, 0xff, nullptr, 0}},
IRQ_LPI2C1
IRQ_LPI2C1
};
TwoWire Wire(&IMXRT_LPI2C1, TwoWire::i2c1_hardware);

PROGMEM
constexpr TwoWire::I2C_Hardware_t TwoWire::i2c3_hardware = {
CCM_CCGR2, CCM_CCGR2_LPI2C3(CCM_CCGR_ON),
CCM_CCGR2, CCM_CCGR2_LPI2C3(CCM_CCGR_ON),
{{17, 1 | 0x10, &IOMUXC_LPI2C3_SDA_SELECT_INPUT, 2}, {36, 2 | 0x10, &IOMUXC_LPI2C3_SDA_SELECT_INPUT, 1}},
{{16, 1 | 0x10, &IOMUXC_LPI2C3_SCL_SELECT_INPUT, 2}, {37, 2 | 0x10, &IOMUXC_LPI2C3_SCL_SELECT_INPUT, 1}},
IRQ_LPI2C3
IRQ_LPI2C3
};
TwoWire Wire1(&IMXRT_LPI2C3, TwoWire::i2c3_hardware);

PROGMEM
constexpr TwoWire::I2C_Hardware_t TwoWire::i2c4_hardware = {
CCM_CCGR6, CCM_CCGR6_LPI2C4_SERIAL(CCM_CCGR_ON),
CCM_CCGR6, CCM_CCGR6_LPI2C4_SERIAL(CCM_CCGR_ON),
{{25, 0 | 0x10, &IOMUXC_LPI2C4_SDA_SELECT_INPUT, 1}, {0xff, 0xff, nullptr, 0}},
{{24, 0 | 0x10, &IOMUXC_LPI2C4_SCL_SELECT_INPUT, 1}, {0xff, 0xff, nullptr, 0}},
IRQ_LPI2C4
IRQ_LPI2C4
};
TwoWire Wire2(&IMXRT_LPI2C4, TwoWire::i2c4_hardware);




// Timeout if a device stretches SCL this long, in microseconds
#define CLOCK_STRETCH_TIMEOUT 15000


void TwoWire::setClock(uint32_t frequency)
{
port->MCR = 0;
port->MCR = 0;
if (frequency < 400000) {
// 100 kHz
port->MCCR0 = LPI2C_MCCR0_CLKHI(55) | LPI2C_MCCR0_CLKLO(59) |
LPI2C_MCCR0_DATAVD(25) | LPI2C_MCCR0_SETHOLD(40);
port->MCFGR1 = LPI2C_MCFGR1_PRESCALE(1);
port->MCFGR2 = LPI2C_MCFGR2_FILTSDA(5) | LPI2C_MCFGR2_FILTSCL(5) |
LPI2C_MCFGR2_BUSIDLE(3900);
LPI2C_MCFGR2_BUSIDLE(3000); // idle timeout 250 us
port->MCFGR3 = LPI2C_MCFGR3_PINLOW(CLOCK_STRETCH_TIMEOUT * 12 / 256 + 1);
} else if (frequency < 1000000) {
// 400 kHz
port->MCCR0 = LPI2C_MCCR0_CLKHI(26) | LPI2C_MCCR0_CLKLO(28) |
LPI2C_MCCR0_DATAVD(12) | LPI2C_MCCR0_SETHOLD(18);
port->MCFGR1 = LPI2C_MCFGR1_PRESCALE(0);
port->MCFGR2 = LPI2C_MCFGR2_FILTSDA(2) | LPI2C_MCFGR2_FILTSCL(2) |
LPI2C_MCFGR2_BUSIDLE(3900);
LPI2C_MCFGR2_BUSIDLE(3600); // idle timeout 150 us
port->MCFGR3 = LPI2C_MCFGR3_PINLOW(CLOCK_STRETCH_TIMEOUT * 24 / 256 + 1);
} else {
// 1 MHz
port->MCCR0 = LPI2C_MCCR0_CLKHI(9) | LPI2C_MCCR0_CLKLO(10) |
LPI2C_MCCR0_DATAVD(4) | LPI2C_MCCR0_SETHOLD(7);
port->MCFGR1 = LPI2C_MCFGR1_PRESCALE(0);
port->MCFGR2 = LPI2C_MCFGR2_FILTSDA(1) | LPI2C_MCFGR2_FILTSCL(1) |
LPI2C_MCFGR2_BUSIDLE(3900);
LPI2C_MCFGR2_BUSIDLE(2400); // idle timeout 100 us
port->MCFGR3 = LPI2C_MCFGR3_PINLOW(CLOCK_STRETCH_TIMEOUT * 24 / 256 + 1);
}
port->MCCR1 = port->MCCR0;
port->MCFGR0 = 0;
port->MCFGR3 = LPI2C_MCFGR3_PINLOW(3900);
port->MFCR = LPI2C_MFCR_RXWATER(1) | LPI2C_MFCR_TXWATER(1);
port->MCR = LPI2C_MCR_MEN;
port->MCCR1 = port->MCCR0;
port->MCFGR0 = 0;
port->MFCR = LPI2C_MFCR_RXWATER(1) | LPI2C_MFCR_TXWATER(1);
port->MCR = LPI2C_MCR_MEN;
}

#endif

+ 2
- 0
WireIMXRT.h Просмотреть файл

@@ -151,6 +151,8 @@ public:
private:
//void isr(void);
//bool wait_idle(void);
bool wait_idle();
bool force_clock();
IMXRT_LPI2C_t * const port;
const I2C_Hardware_t &hardware;
uint8_t sda_pin_index_ = 0x0; // default is always first item

Редактирование Предпросмотр
Загрузка…
Отмена
Сохранить